Main use is development, 3D modeling, and some artwork. I do play 3D games occasionally, mainly Minecraft and World of Warcraft, occasionally others, but nothing that requires top of the line parts. it only makes sense if a single three-head card is more expensive than two dual-head cards and water cooling (which would mean radiator, pump, reservoir, tubing, etc).Īccording to Everest, as I am typing this post with nothing else happening on the PC, my temps are:įan speed for both GPU's is 100% I leave it there all the time now, using the auto setting in precision would never set the fan speed above 80%, even when the temp on GPU1 was approaching 100 c. I don't want to spend a ton of extra money on the cooling though. I don't mind going to a water cooled solution, if that is necessary (my CPU is water cooled via H50). It’s powered by the NVIDIA Ada Lovelace architecture and comes with 24. Experience ultra-high performance gaming, incredibly detailed virtual worlds, unprecedented productivity, and new ways to create. It brings an enormous leap in performance, efficiency, and AI-powered graphics. What I think I need is a single card that can drive three monitors, or a much better two-GPU setup. The NVIDIA® GeForce RTX 4090 is the ultimate GeForce GPU. Oh, and I'm running the latest drivers, this has been going on for the last three versions, at least. I've swapped them around a few times, hoping to get more life out of them, but it's time to replace them. I've started getting blue screens on boot up, and driver recover messages, all pointing to the cards failing. The main card is constantly over heating, there's just not enough room between the two cards for air cooling. Make sure it's disabled.Hey guys, I am currently driving three 23" LCDs on two GeForce GTX 285's in SLI. Maybe it has something to do with windows fast startup. NVCP has multimonitor setup correctly, same as windows.Windows 10 has correct settings for primary and secondary monitors.Why would my 1070 start the monitor on the displayport ONLY on a restart? Now here's the kicker - if i unplug my secondary monitor (DVI) and start with just the primary connected (displayport) it works fine, but there is a distinct pause in the bot -almost like it's restarting of own accord - before the monitor lights up. Starting my PC, then restarting it, every time, to get both monitors working, gets old. It always boots to DVI (which from the above I understand is the priority of the card) but the main monitor doesn't start at all - unless I restart the PC, in which case it comes on after the other monitor. I'm running my primary monitor off the displayport and the secondary off the DVI. Initialization order in first place seems to be HDMI and not DVI.! You obviously can’t use a port that doesn’t support audio and expect it to give you audio. use display port to hdmi adapters or use hdmi adapters. NOTE: You can not do this when you have 4K TV connected because the DVI does not support sound but only video.! If you hook up the DVI to TV then no audio on that HDMI port.!!! Unfortunately, doing that myself is beyond my abilities. I was just hoping it was possible but I don't think it is without a modified BIOS/Firmware. This would have to be a change made to the GPU hardware/firmware. The same with your motherboard BIOS it doesn't set GPU display port initialization order. Since this is all occurring prior to the OS and drivers being loaded, no amount of fiddling with them will make any difference. You can't change the order of the boot initialization of the ports on the GPU. Not the HDMI or DVI's.Īs far as I know, the display port initialzation order is DVI, HDMI, DisplayPort. I want the computer to post to the video cards display-port. It uses the display-port because its a 4k monitor and requires a display-port to run at 4k with 60hz. I CANNOT move the cables of the primary monitor. If you are trying to get a specific display to show, and changing the cable won't work, try shuffling monitors. S., if the computer is completely shut down when you do this, it won't know you disconnected any displays. Once complete, go into Windows, and configure the monitors and main display in the control panel. Take the cable that is now free and move it to the other monitor that used to have the boot screen. Simply unplug the cable from the one that is currently booting, and move that cable to the one you want the boot screen and bios to appear on. Once you are in Windows, set the default main screen you want.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |